Types Of Bathtub Drains

bathtub drain stopper types


Although all of them function exactly the exact purpose--to keep water from the bathtub when needed and also invite the tub to become emptied again--there are a number of distinct varieties of bathtub drain stoppers. The most ordinary types of tub drains are all lift-and-turn, push-and-pull, popup, toe-touch, flip-it, and trip lever.


Identifying which type you've got will assist you to when it's essential to repair or change out your drain stopper. Some kinds of drain stoppers may ensure it is rather catchy to routinely clean out the drain of debris and hair.

Here are just six common types of tub drains to assist you identify yours.


Even a lift-and-turn drain stopper is identified by a little knob on the cap of this drain stopper, and it is utilised to spin the stopper open and closed. Even a lift-and-turn stopper is shut by turning the knob onto the cover of the stopper until it moves , and it is started by lifting and turning the knob in the other direction.

This type of stopper is set up by screwing a centre setscrew in to the threaded centre of the drain cross-bar. The set-screw lies underneath the top cover of this stopper. Removing a lift and twist stopper can be considered a small tricky if it was over-tightened when 1st put in or if it's not been taken off in some moment; point.

But mechanically, this is an incredibly simple style that rarely desires much attention, apart from sporadically getting rid of the plug to rid the drain of debris and hair.






Even a push-and-pull stopper is really like a lift-and-turn stopper in design and look, however, it was pushed down to close and dragged up to open instead of twisting to close and open. Setup is also much like with the stopper human body attached with the drain using a setscrew discovered beneath the cap of the stopper.

And also this is really actually a exact easy mechanical layout and style that rarely takes much from the method of repair.


A Toetouch stopper (also called a toe-tap or foot-actuated) is carefully associated with the lift-and-turn as well as the push-and-pull stopper. This kind uses a design layout, and the stopper human body is kept set into the cross bar over the drain fitting using a screw located beneath the cap of their stopper. To close or open the stopper you simply push down it along with your own toe.

Like the bathtub drain stopper types, this one is fairly small, even although sometimes the spring mechanism could tear out, demanding that you simply exchange the stopper.


Even a flip-it bathtub stopper is readily installed without the tools essential. A toggle lever connected directly to the top of the stopper is moved from side to side to open and close the stopper. To put in such a stopper, you simply push it to the drain; the ​built-in O-rings hold it into position and create a watertight seal.

Vacation Lever

The vacation lever stopper is just one of 2 types featuring a lever entirely on the overflow plate at the front part of the tub. In this very first class, there is no visible pop-up stopper in the drain opening--simply a strainer.

This stopper works using a plunger from the bathtub overflow pipe, which goes up and right down into close and open up the tub's drain pipe. Even the plunger is linked towards the trip lever having a linking rod found inside the overflow tube. With all the trip lever the plunger is raised and the drain is open; once the excursion lever is up, the plunger is pushed down and also the drain is closed.

This stopper form is somewhat tricky to remove for cleaning, as it has to be pulled by pulling this up throughout the overflow tube and also out of the overflow plate.

A variation of this type does not use a lever, but alternatively a twist cover on the over flow plate that rotates left and to lift and lower the plunger.


The drain component of the type of bathtub stopper looks much like a bathroom sink pop-up. And it is like the trip-lever stopper as it is operated by the same kind of lever onto the overflow plate. After the lever goes, the connecting rod linkage from the over-flow drainpipe moves and pivots a rocker arm that joins to the pop up stopper. At the bottom end of the linking rod can be just actually a spring that presses down against the rocker arm to operate the stopper.

This stopper form may likewise be a little difficult to completely wash considering that the stopper and also rocker arm has to be extracted by means of the drain opening, and the connecting rod linkage must be extracted up through the overflow pipe and outside via the overflow plate.

The complexity of the mechanism makes this types of bathtub drains more susceptible to collecting debris and hair .